Tops Knives Hunters of Gunmen Fixed Blade Knife Black 4.38in

Tops Knives Hunters of Gunmen Fixed Blade Knife Black 4.38in. HOG means Hunter Of Gunmen because we hunt men with guns. We HOGs are a force multiplier for any commander that chooses to employ us. The design for this blade started somewhere in my history that I cannot fully trace. It began in the early years of my career as a young Marine Infantryman. After spending days or weeks at a time in a field environment it seemed that my hands would always ache. I eventually traced this pain back to the blades that I was carrying and using. The Tacti-cool handles on those blades all had rough edges and sharp corners. Sure they were mean to look at and gripped like a gator but they didn't have the comfort that I needed for sustained field use. After this realization I set out to design the best knife handle that I could in my limited experience. Little did I know at the time this would take the better part of my career to complete. I started with a piece of wooden closet rod and carved in the features that I most liked in many of the knives that I have used. I kept this in my pack for a long time and modified it with a piece of sandpaper as I discovered new ways to use a knife. Whenever one of my field knives earned me a hot spot I grabbed that little handle mock up and made a subtle change so that it did not irritate that hot spot. This went on for many years and many times this piece was over worked and restarted new. Eventually I had the handle shape that worked wonderful in my hand. So I looked to buy a knife that had a handle close to the one that I had designed. I found one and set out on the next phase of simply using the blade as much as possible while making subtle changes to the handle. This also led to my developing a greater understanding of how to use a knife to accomplish field tasks while also conserving energy. With the handle done I realized that there was another problem brewing. The blade designs were just not up to the task that I needed them for. Some of the better shapes were too thick and some too flimsy. Some had bad edge geometry that would just not hold the keen edge needed for a good field knife. This continued through out many years and on to my instructor position at the 1st Marine Division Scout Sniper School. I was fortunate in that I was the primary instructor for survival fieldcraft and combat tracking. This gave me the opportunity to sample many many knives that my students had in their kit. Believe me Snipers love knives like coyotes love meat. In doing this I developed an attraction to wide blades with keen edge geometry. The problem was that there were not any available that I could find that would meet both my blade and handle requirement. Not that I was the expert but I knew what I needed and that was good enough for me. So now I was armed with this Ideal field knife that does not exist. So I set out to make this knife exist. I made a wooden knife from start to finish and carried that in my pack everywhere so every time that I had an issue with whatever knife I was carrying I could sand my wooden blank to remedy it. Some Marines thought that I was crazy being a Marine Sniper in the field with a wooden knife in my pack. I just claimed that I was doing research and development that usually quieted wanna-bes and mall ninjas. Nevertheless I continued to refine the design. Fast forward a few deployments and I landed a job at the Mountain Warfare Training Center as the SNCOIC of Mountain Survival and Mountain Scout Sniper Courses. Of course that meant lots of field time. In order to be a qualified red hat you have to complete winter and summer mountain leader courses and that means practically living on the mountain. I continued to refine the design until I could think of no more refinements. Then one time on the mountain while skinning a rabbit I set my knife in the snow and the knife disappeared. Already half starved there was no way that I was going to dig down and retrieve it so I went back to the drawing board with my knife design. I wanted a way to retain my blade and not have to have six feet of dummy cord attached to it. That is when the hole was born. I made the hole big enough to handle a standard issue carabineer so that it could be clipped to my gear rather than set on the ground when working. It is a bad ideal to put a bloody blade back in the case while skinning game if you do you will only do it once after you learn that lesson. This worked well and eventually I discovered many uses for that hole. When I thought that I had the design about as good as I could make it I sent it and a larger version of it to my good friend and mentor Ron Hood. I had asked for his opinion on the overall design and I asked him if he could find any obvious flaws in the design that I may have overlooked. Ron never got back to me as he was busy with his new magazine and all the other projects that he had going on. So I let the issue rest. At first I figured that Ron must not have liked it but